
How a house receives power in two halves
To understand why half a house can go dark, it helps to know how electricity arrives. Most American homes, including most in South Florida, receive what is called split phase service. Three wires come from the utility transformer to the meter. Two of them are hot legs, and the third is the neutral. Each hot leg carries alternating voltage of about half the total between the two legs. Between either hot leg and the neutral, you get the standard voltage used by lights, outlets and small appliances. Between the two hot legs together, you get roughly double that voltage, which is what large appliances such as the range, the dryer, the water heater and the air conditioner use.
Inside the panel, the two hot legs run down the two sides, and breakers are arranged so that their positions alternate between one leg and the other. A single pole breaker takes power from one leg. A double pole breaker, which is two breakers joined by a handle, takes power from both. So some circuits in your house are on one leg, some on the other, and large appliances use both.
Now consider what happens if one of the two legs stops delivering power. Everything connected only to that leg goes dark. Everything connected only to the other leg keeps working. Appliances that need both legs, such as the dryer, the oven and often the air conditioner, will not work properly, and some may behave oddly. The meter is still turning because the other half of the house is still drawing power. This is the situation people describe when they say, half the house lost power and the meter is still running.
The same effect can come from other causes. A tripped main breaker affects the entire house, but a tripped double pole breaker, or an issue in a subpanel, can knock out a large portion of the house. A failed connection inside the panel can remove power from half the bus. A fault in the utility service can drop one leg before the power even reaches the meter.
Many Cooper City homes date from the 1970s onward, and the service equipment in them has been in place for decades. Humid South Florida climate is hard on connections at the meter, the main breaker and the service wires. That does not mean every house will have a problem, but it explains why partial power loss is a pattern electricians see often in established neighborhoods.
This guide proceeds step by step. First we rule out the simple, harmless explanations. Then we look at the more serious cause, a lost leg or a failing neutral, which can actually damage equipment. We explain who is responsible for which part of the system, what you can do safely while waiting, and what an electrician will do to repair it.
First, rule out the simple explanations
Before assuming the worst, take a few minutes to look for ordinary causes. Many partial outages turn out to be simple, and finding that out saves worry and expense. These steps are safe for any homeowner when done carefully, because they involve looking and pressing a switch on a panel cover that is closed. Do not remove the panel cover.
Start by making a map of what is out. Walk through the house and note which lights, outlets and appliances have no power. Look for a pattern. Are they in one part of the house, or scattered all over? Scattered across many rooms suggests a leg problem, because circuits on the same leg are spread around the house without regard to location. Concentrated in one area suggests a single circuit or a group of circuits, which suggests a breaker or a ground fault device.
Then check the following:
- Ground fault outlets. These have test and reset buttons. In garages, bathrooms, kitchens and outdoors, one tripped device can cut power to several outlets downstream, sometimes in other rooms. Press reset on any that have tripped.
- The panel. Without removing the cover, look at the breakers. A tripped breaker sits in a middle position, or the handle is flush in the off position. To reset, push firmly to full off and then to on. If it trips again immediately, stop and call.
- The main breaker. If it has tripped, the entire house will be dark. If it is on, power to the panel from the service is presumably present on at least one leg.
- Neighbors. Look outside. If neighbors also have partial or full outages, the cause is likely on the utility side.
- Weather. Afternoon thunderstorms are frequent in Broward County. A nearby lightning strike or a gust that disturbed a wire can cause partial outages.
If you find a tripped breaker and resetting it restores power, make a note of which one it was. A breaker that trips once may have responded to a temporary overload. If it trips again, there is a reason, and it deserves investigation. Resetting it repeatedly can overheat the breaker or the wire.
If you find a double pole breaker tripped, it may have handled a large appliance, such as the water heater, the air conditioner or the dryer. A trip on one of these can cause part of the house to go dark if that breaker feeds a subpanel. Look for a label.
Also check whether any large appliance is behaving strangely. A dryer that tumbles but does not heat, an electric range with burners that work on only one side, or an air conditioner that runs the fan but not the compressor can each indicate one leg is missing. These are good clues to share with an electrician, and they are strong signs of a lost leg in the supply.
If none of these steps restore power, or if you find signs of heat, scorching, odd noises or burning smells, move on to the next sections, and do not keep experimenting.
A lost leg, a weak neutral, and why lights sometimes run bright
When simple causes are ruled out, the next suspects are a lost hot leg and a failing neutral. These are different problems with different symptoms, and one of them can damage equipment.
A lost hot leg is the situation described above: one of the two hot wires is not delivering power. The circuits on that leg are dead, while the circuits on the other leg are fine. The 240 volt appliances do not work. The cause may be a break or bad connection anywhere upstream: in the wires from the transformer, in the meter, in the main breaker or in the panel's internal connections.
A failing neutral is more subtle and more dangerous. The neutral wire provides the return path for current and keeps the voltage balanced between the two halves of the house. If the neutral connection is lost or becomes loose, the voltage between each hot leg and the neutral no longer stays at the correct value. Instead it shifts depending on how much load is on each side. One side may receive a higher voltage than it should, while the other receives less. The result can be lights that are unusually bright on one side and dim on the other, a television that flickers or smells hot, or equipment that fails.
Signs of a neutral problem include:
- Some lights extremely bright while others are dim, particularly at the moment an appliance starts or stops.
- A buzzing or sizzling sound from the panel or the meter.
- Electronics, such as a router, a television or a refrigerator control, failing without explanation.
- A smell of hot plastic or burning near the panel or meter.
- A tingling feel when touching a metal appliance, a faucet or a metal part of the panel cover.
These signs are urgent. A neutral problem can send excessive voltage into half the house and burn out equipment. If you see lights becoming very bright or you smell burning, shut off the main breaker if you can reach it safely, avoid using appliances and call the utility and an electrician. If you see flames or smoke, leave the house and call emergency services.
It is important to emphasize that you should not try to diagnose which of these conditions you have by touching wires or using a cheap tester inside the panel. The service conductors that feed the main breaker remain live even when the main breaker is off. Contact with them can be fatal.
Humidity and heat play a role in how these problems develop. Moist air promotes corrosion at the meter socket and at lugs, while thermal cycling loosens screws. A connection that is slightly loose carries current with a bit of heat each time. Over years, the heat degrades the metal and insulation until the connection fails, sometimes dramatically. A house with an older panel or service is more likely to have such failures than one with newer equipment, but age alone does not predict it.
Knowing the difference helps you describe the situation to the utility and the electrician. If you can tell them that half your circuits are dead and the 240 volt appliances are not working, they will have a good idea where to start.
Who owns which part of the fault, and who to call first
One of the most useful things to know in a partial outage is who is responsible for each part of the system. The answer decides whom you call first and what they are permitted to touch.
The general arrangement is as follows. The utility owns the transformer, the wires from the transformer to the meter, and the meter itself. In many cases, the utility's responsibility extends to the point where its wires connect to your service equipment. If the service is overhead, the wires that run from the pole to the house and attach at the weatherhead are typically the utility's up to a connection point. If it is underground, the utility's responsibility often ends at the meter base or at a connection on the property. The details vary, so it is wise to ask the utility where its responsibility ends at your address.
The property owner is responsible for the equipment from that point onward: the meter base or socket if owned by the customer, the service mast and conduit, the main breaker, the panel, and all the wiring inside the building. Some utilities do own the meter socket, while others consider it the customer's. Again, ask.
With that in mind, here is how to decide whom to call:
- If neighbors are also affected, or you see downed or damaged lines, call the utility. The problem is almost certainly in their equipment. Stay away from any downed wire and keep others away.
- If you see sparks, burning or damage at the meter or the service mast, call the utility's emergency line and, if there is fire, emergency services.
- If only your house is affected and the breakers look normal, call the utility and an electrician. The utility can check its side, and an electrician can check yours. Often the utility will test their equipment first and tell you if the fault lies beyond the meter.
- If you found a tripped breaker that will not reset, or a damaged panel, call an electrician.
When you call the utility, give them as much specific information as possible. Tell them that your house has partial power, that the main breaker is on, that some circuits are dead and that you suspect a lost leg. Say whether neighbors are affected. Mention any noises or smells. Specific descriptions help them send the right crew.
Some utilities will check the meter and the connections to it. If they find the problem on their side, they repair it. If they find that the problem lies in your equipment, they will tell you, and may disconnect service for safety until it is repaired, particularly if there is a risk of fire. Do not be alarmed by this. It is a protective measure.
After a repair by the utility, check that everything has returned to normal. Check appliances, particularly electronics, for signs of damage. If any equipment was affected by a neutral problem or a surge, note it, because documenting damage may matter for any claim.
Finally, if the cause turns out to be inside your equipment, the utility may require an inspection before it will restore service. An electrician can arrange the permit and the inspection, a process that varies by situation.
Staying safe while you wait for help
While you wait for the utility or an electrician, a few precautions reduce risk and protect your equipment. These are practical steps that do not require opening anything.
The most important rule is to treat the dead half of the house with the same respect as the live half. Circuits that appear dead may be reenergized suddenly when the repair is made, or when a loose connection makes contact again. Do not assume that a dead outlet is safe to work on. Do not open a light fixture or an outlet because it has no power.
Here are other precautions to follow:
- Reduce the load. Turn off or unplug sensitive equipment, such as televisions, computers, routers and gaming consoles, to protect them from a sudden surge when power returns or from a neutral problem.
- Turn off large appliances. Switch off the air conditioner at the thermostat, the dryer, the range and the water heater breaker, so they do not all start at once.
- Leave one light switched on. A light in a room helps you notice when power is restored. Choose one on the working half.
- Watch for brightness changes. If lights become noticeably brighter or dimmer, or you smell burning, shut off the main breaker if it is accessible and safe, and call.
- Keep the panel clear. Make sure the area has no boxes or storage in front of it so access is easy.
- Protect food. Keep the refrigerator and freezer doors closed. If the refrigerator is on the dead half, food will stay cold for a limited time, and you may want to move it to the working half using a heavy duty extension cord if a safe outlet is nearby, or simply keep the door closed until help arrives.
Be careful with extension cords. If you run a cord from a working outlet to power a refrigerator, use a cord rated for the load and keep it off wet floors. Do not overload a single outlet or run a cord under rugs. If you are unsure, leave the refrigerator closed and wait.
If you use a generator, never connect it to a household outlet or panel to feed the house, and never run it in a garage or near open windows. The exhaust contains a gas that is colorless and odorless and can be deadly. Place the generator outdoors, well away from the building, and use heavy duty cords. A generator connected improperly can also feed power back onto the utility lines, which endangers line workers. A properly installed transfer switch prevents that.
If anyone in the household depends on medical equipment that needs power, treat the outage as urgent. Move the equipment to a working circuit if it is safe, use its battery if it has one, and contact your medical provider or emergency services if needed.
Humid South Florida climate means that panels and meters can be damp after rain. If you must go near the meter or panel, keep your hands dry, stay on dry ground and do not touch metal parts. In wet conditions, wait for the professional.
What the repair involves and how to prevent a repeat
Repair depends on where the fault is. An electrician starts by confirming the symptom and then measuring the voltage at several points, a process that works from the outside in. Measurements at the meter, at the main breaker, at the panel bus and at individual breakers show where voltage disappears or goes wrong. This is called tracing the fault, and it is precise. The electrician does not guess.
Typical repairs include:
- Replacing a failed main breaker. A main breaker can fail internally so that one pole no longer passes current. Replacement restores the lost leg.
- Repairing or replacing the meter socket. If the socket jaws are burned, loose or corroded, they may need to be replaced, with the utility's coordination because it involves disconnecting service.
- Tightening or replacing lugs and connections. Where a connection has been running hot, the electrician replaces damaged parts rather than simply tightening.
- Replacing the panel. If the busbar is damaged or the panel is old and has been affected by corrosion, replacement may be the most reliable answer.
- Repairing the service entrance cables or mast. If the wires between the weatherhead and the meter are damaged, replacement is needed.
- Repairing a damaged neutral connection. This may involve both the electrician and the utility, depending on where the break is.
Many of these repairs require a permit and an inspection, since they involve the service. They may also require the utility to disconnect and reconnect power. The electrician normally coordinates this. Expect that power will be off for part of the day.
After the repair, ask the electrician to explain what failed, what they replaced and whether other parts show signs of similar wear. Ask them to label the panel clearly. Test the appliances that were affected. Keep any documentation.
Prevention is mostly about attention. Look at the panel and meter area from time to time, checking for rust, moisture, discoloration or buzzing sounds. Keep the area clear and dry. Avoid overloading circuits. Consider surge protection at the panel, which helps protect electronics from spikes. If your home's service equipment is old, consider asking an electrician for an assessment, particularly if you have seen flickering lights or breakers that trip.
If you notice early warning signs, such as lights that flicker, a warm panel or a buzzing noise, do not wait for a full outage. Early repair is usually simpler and safer than repair after failure.
If you are dealing with partial power loss right now, call and describe what you have found. A quote can begin by phone, but because this involves the service and the panel, an on site visit is needed before anyone can tell you the exact repair. In the meantime, keep safe, keep your distance from the meter and panel, and let the professionals do the work.