Call (954) 568-8474
Home / Services / Generator Hookups

Standby Generator Connections for Hurricane Season

Hurricane season runs from June 1 to November 30, and storms that pass through Broward County can leave neighborhoods dark for a long time. This page explains the safe ways to connect a generator to a house, why a transfer switch matters, and how to plan before the watch is posted.
Illustrative photograph

Why how you connect a generator matters more than which one you buy

When a tropical storm knocks out power across Broward County, the instinct is to get a generator running as quickly as possible. That instinct is understandable, but the way a generator is connected to a house is a safety question before it is a convenience question. A generator that is connected incorrectly can harm the people inside the house, the people working on the power lines outside, and the generator itself.

The central danger is called backfeed. The utility system is designed so that power flows from the lines to the house. If a generator is wired into the house wiring without a proper means of separation, power can flow the other direction, from the house out through the meter and onto the lines in the street. A lineworker who believes a line is dead because the grid is down may be exposed to a live conductor. Neighbors on the same transformer can also be affected. This is why connecting a generator by plugging a cable with two male ends into a wall outlet, sometimes called a suicide cord, is dangerous and illegal in many places. It is the reason proper equipment exists.

The correct approach is to isolate the house from the utility before the generator supplies it. This can be done with a transfer switch, which is a device that connects the house to either the utility or the generator but never both at once. It can also be done with a mechanical interlock that physically prevents the main breaker and the generator breaker from being on together. Either method, installed according to code and with a permit, makes it impossible to backfeed the grid.

Beyond backfeed, there are other safety points. Generators produce carbon monoxide, a colorless, odorless gas that can build up quickly in enclosed spaces, including garages and screened lanais. Fuel storage and refueling carry fire risks. Overloading a generator can damage equipment. And water and electricity do not mix, which is a particular concern when storm rain and flooding follow a power outage. All of these factors point toward planning in advance rather than improvising in the dark.

The other thing worth saying is that a generator connection is not a large project in the context of a house. Compared with a rewire or a panel replacement, installing an inlet box and a transfer arrangement is usually a modest job, and it is far less stressful when done in calm weather in July than during a storm warning in September. Families who have lived through a long outage often say the planning was the best money they spent. We are not making promises about outcomes, but the logic is simple: a safe connection that is already in place makes the first night of an outage much easier.

If you already own a generator or are thinking about buying one, bring the make, the output rating and the type of outlets it has to the first conversation. The right connection depends on the generator as well as the house, and a quick description by phone lets the electrician plan the on site visit.

The inlet box, the cord and the interlock: the common portable setup

For households that own a portable generator, the most common safe arrangement has three parts: a power inlet box on the outside wall, a heavy cord, and a panel arrangement that keeps the generator and the utility from connecting at the same time.

The inlet box is a weatherproof receptacle mounted on the exterior of the house, usually near the panel or near the place where you plan to set up the generator. It looks like a small gray or metal box with a plug style connector built in. Instead of running a bundle of extension cords through a window or door, you plug one heavy cord from the generator into the inlet. Because the connector is rated for outdoor use and the cord is made for the job, the connection is much safer than a makeshift run through a window. It also keeps rain and humidity out of the cord's connection point, a real concern in Florida weather.

Inside the house, the inlet is wired to a dedicated breaker in the panel or to a transfer arrangement. With an interlock kit, a mechanical slide is installed over the main breaker and the generator breaker. When the utility is on, the slide allows the main breaker to be on and keeps the generator breaker off. When the utility is down, you switch off the main, slide the interlock, and then switch on the generator breaker. The interlock is what prevents the two sources from ever being on together. It is simple and reliable when installed correctly, and it lets you power any circuit in the panel as long as the generator can handle the load.

The disadvantage of the interlock approach is that you have to manage the load manually. Because every circuit in the panel is available, it is easy to turn on too many things at once and overload the generator. You must decide ahead of time which circuits you will use and keep the large ones, such as the air conditioner, the electric range and the water heater, off unless the generator is sized for them. A written list of safe circuits taped near the panel helps everyone in the family follow the plan, even when it is dark and stressful.

The cord is another detail worth getting right. It should be rated for the current of the generator and the outdoor environment, in good condition, and long enough to place the generator at a safe distance from the house without being stretched. Store it dry and coiled so the connectors stay clean. Corrosion in a Florida garage is real, and a connector that has been sitting in damp air for a few months may need cleaning before use.

Before the storm season, practice. Run the generator in the open driveway, plug in the cord and operate the panel according to the plan. A dry run shows whether the cord reaches, whether the generator starts easily after sitting, and whether everyone knows the steps. It is surprising how many problems show up in a ten minute rehearsal that would have been miserable to discover in the dark. After the test, label the panel with the sequence and shut the generator down following the manufacturer's directions.

Transfer switches: choosing between manual, circuit specific and automatic

A transfer switch is the other proven way to connect a generator. Rather than relying on a mechanical slide at the main breaker, it uses a purpose built switch that moves selected circuits from the utility to the generator. There are several kinds, and understanding them helps you match the equipment to your needs.

A manual transfer switch for a portable generator is a small subpanel installed next to the main panel. It contains a handful of circuits that you have chosen to back up, perhaps six to ten. The circuits are moved from the main panel to the transfer switch panel. In normal times, power flows from the utility through the switch to those circuits. During an outage, you start the generator, plug it into the inlet and flip each circuit's switch to the generator side. Because only the circuits you selected are connected, you cannot overload the generator by turning on everything at once. This approach suits a household that has a modest portable generator and a clear list of essentials: the refrigerator, a few lights, a fan, the router and perhaps a freezer.

An automatic transfer switch goes a step further. It senses when utility power is lost, signals a permanently installed standby generator to start, and moves the load without anyone touching it. When utility power returns, it switches back and tells the generator to shut down. Standby generators are fueled by natural gas or propane and mounted on a pad outside the house. They are a larger investment and need permits, a fuel supply, and a sound installation, but they provide convenience for households with medical needs, home offices or members who cannot manage a manual process.

A few questions will help you choose:

  • How long are you prepared to be without power, and what do you need to keep running in that time?
  • Is anyone in the household dependent on powered medical equipment or refrigerated medication?
  • Do you want to start the generator by hand, or would you prefer it to come on automatically?
  • How much do you want to power: a few essentials, or most of the house including air conditioning?
  • Is there a place to put the generator that keeps exhaust away from windows, doors and neighbors?

Air conditioning deserves a separate thought. In Florida summers, a house without air conditioning is uncomfortable, and for some people unsafe. A central system draws substantial current, especially when the compressor starts, and a portable generator that powers essentials may not be able to run it. A larger standby unit or a carefully planned selection of one system can address this. If cooling is a priority, mention it at the start so the generator and the transfer equipment are sized with it in mind.

One more practical point: a transfer switch is only as good as its installation and its documentation. Ask for the circuits to be labeled both at the switch and at the main panel, and get a simple diagram of which is which. Having this on paper spares you from guessing when a storm is on the way.

Sizing the generator and the circuits it will carry

Generators are rated in watts, and the rating is split into a running figure and a starting figure. Appliances with motors, such as refrigerators, freezers, well pumps and air conditioners, draw a surge of power when they start, often several times what they need to keep running. A generator must be able to handle that surge in addition to everything else running. This is why a small unit may run lights and a television comfortably but struggle with a refrigerator on top of them.

To size a generator, list the items you want to power and find the running and starting wattage for each, which is often printed on a label on the appliance or in its manual. Add the running watts of everything you expect to operate together, then add the largest starting surge on top. That total gives a rough target. Leave a margin, because a generator running at its limit for days is under stress and burns more fuel.

A typical household essentials list might include the following:

  • The kitchen refrigerator and the garage freezer, which protect food.
  • Several lights in the areas where the family gathers.
  • Fans, which make a hot night tolerable.
  • The modem, router and chargers for phones and laptops.
  • A microwave or a small cooking appliance, used one at a time.
  • A sump or well pump if the property has one.
  • Medical equipment, where applicable, with its own plan.

Circuits matter too. The wire and breaker for the generator inlet have to match the output of the generator. A common portable generator may deliver power at a standard household voltage through a twist lock connector. The inlet box, the cord, the breaker in the panel and the wire in between must all be rated for the same current. An undersized link in this chain will heat up. This is another reason not to buy an inlet box and cord based on a quick look at a shelf and a guess. The components should be specified together.

Some families wonder about powering the whole house. It is possible with a large standby generator, a properly sized transfer switch and a gas supply, but it is a significant project. A more common compromise is to select a group of circuits that provide comfort and safety. Many people find that the kitchen, a bedroom or two, the family room and one air conditioning system cover what they need. Planning these choices when the weather is calm is much easier than deciding at midnight.

Consider fuel as well. Gasoline powered portable generators require stored fuel, and fuel stored for a long time degrades. Gas stations may have long lines or be closed after a storm. Standby units that run on natural gas depend on the gas line staying in service, which has generally been dependable but is not guaranteed. Propane requires a tank on site. Each approach has trade offs in cost, maintenance and convenience. There is no single right answer, and a candid conversation about what suits your household is more useful than a sales pitch.

Where to put it, how to fuel it and how to avoid carbon monoxide

The most important rule about generator placement is simple: it goes outdoors, and well away from the house. A generator must never be operated inside a garage, even with the door open, inside a screened lanai, in a carport against the wall, or in any other enclosed or partly enclosed space. Carbon monoxide from its exhaust can reach dangerous levels in minutes, and the gas can seep through doors, windows and vents into living areas. People have been harmed because a generator was running in a garage with the door cracked open. The rule has no exceptions.

Place the generator on level ground in the open, at a distance from doors, windows and vents so that exhaust does not drift into the house. The manufacturer's manual states the minimum distance, and it should be followed. Think about wind direction, neighbors, and the possibility that the exhaust could be pulled into an air conditioning intake. Keep the unit dry. A generator that gets wet while running is an electrical hazard. A purpose built canopy or a rain shelter designed for generators, with proper ventilation and clearance, lets you run in the rain, while an improvised tarp tied around a running engine does not. Never cover a running generator in a way that traps heat or exhaust.

Battery powered carbon monoxide alarms add a layer of protection. Install them on each level of the house and near bedrooms, and test them before storm season. A battery alarm keeps working when the house power fails. If an alarm sounds, move outside into fresh air immediately and call for help. Do not try to ventilate and go back inside. Symptoms of exposure include headache, dizziness, nausea and confusion, and they can be mistaken for fatigue or a cold, which is part of the danger.

Fueling requires care. Turn the generator off and let it cool before adding fuel, because spilled fuel on a hot engine can ignite. Store fuel in approved containers, outdoors and away from ignition sources, not in a living space. Keep the quantity within reasonable limits and rotate it, using older fuel in a car and replacing it with fresh. Many households add a stabilizer according to the product directions to keep gasoline usable longer.

Maintenance matters between storms. Run the generator periodically, following the manual, to keep the carburetor and the starter in working order. Check the oil, the air filter and the spark plug. Replace the fuel if it is old. A generator that has sat for years often needs service before it will start reliably, which you do not want to discover on the first night of an outage.

Noise and neighbors are another consideration. In a family oriented neighborhood with homes close together, a running generator can be loud. Positioning it so the sound is directed away from bedrooms, and being thoughtful about running hours when possible, helps. Many communities and associations have rules about generator use and placement, so check them ahead of time.

Finally, never refuel, repair or move a running generator, and never plug it into a wall outlet to power the house. Treat it as a tool that earns respect, and it will serve you well.

Before the storm, during the outage and after the lights return

Preparation turns a generator from a source of stress into a source of comfort. Begin well before a storm has a name. In the spring, schedule the installation of the inlet, interlock or transfer switch so it is done and inspected. Test your generator, replace worn parts, and practice the sequence with the whole family. A set of written instructions near the panel helps a teenager or a visiting relative do the right thing if you are not at home.

When a watch is announced, check fuel, cords and alarms. Fill containers according to safe storage guidelines, and move the generator to an accessible location. Charge phones and batteries, and consider topping off a vehicle. Know where your main breaker is and how to turn it off. Do not wait for the last minute, since stores and gas stations fill quickly.

During an outage, follow the sequence you rehearsed. Switch off the main breaker, or use your transfer switch, before starting the generator. Place the generator outdoors, connect the cord, and then close the generator breaker or throw the transfer switch. Turn on circuits one by one, giving the generator time to settle between each, and keep the largest loads off until you know the generator handles them. Watch for signs of strain such as dimming lights, a changed engine sound or a tripped breaker on the generator itself. If that happens, reduce the load.

When utility power returns, do not assume. Switch off the generator breaker first, then shut down the generator, and only then restore the main breaker or move the transfer switch back. This order ensures that the two sources are never connected. Give the house a few minutes to stabilize, then bring appliances back on. Turning everything on at once as power returns can cause a surge of demand, and utilities sometimes see flickering as the grid comes back. It is wise to unplug sensitive electronics during an outage and plug them back in once power looks steady. Whole home surge protection at the panel adds a layer of defense for the moments when power is restored.

After a storm, inspect. Look for damage to the service mast, the meter, the outside wiring and the generator inlet. If the house has flooded, or if there is standing water near outlets and the panel, do not touch anything electrical, and have the system checked before power is restored. Water damaged equipment can be dangerous even after it dries. A qualified electrician can tell you what must be replaced.

Finally, take time to review how the plan worked. Which circuits did you wish you had? Was the cord long enough? How much fuel did you use? Making a few notes while the memory is fresh helps you decide whether to add circuits, change the generator, or consider a standby unit. If you are ready to plan an inlet, an interlock or a transfer switch, start with a call. A quote can begin by phone, and since the work depends on your panel and where the generator will sit, the final plan is confirmed on site.

Generator connection questions from Broward County families

Can I run a cord through a window instead?

It is not a safe or reliable habit. A proper inlet box keeps the connection outdoors, weather rated, and separate from living areas, and it avoids cords pinched in windows.

What is backfeed?

Backfeed is power flowing from your generator back onto the utility lines, which can endanger lineworkers and neighbors. A transfer switch or interlock prevents it.

Interlock or transfer switch, which is better?

An interlock gives access to every circuit but needs careful manual load management. A transfer switch limits you to chosen circuits, which protects the generator. The best choice depends on your list of essentials.

Can a portable generator run my air conditioner?

Only if it is sized for the starting surge as well as the running load. Many are not. State your cooling needs up front so the equipment is sized correctly.

Is a permit required?

Connections to the house wiring are normally permitted and inspected. Standby generators typically need additional approvals. Your electrician can explain what applies.

Where can I run the generator?

Only outdoors and well away from doors, windows and vents. Never in a garage, lanai or carport, even with a door open.

Talk to us

Call to describe your generator and what you want to keep running. A quote starts by phone, and the connection plan is confirmed on site.
Call (954) 568-8474
Call (954) 568-8474