
A small dip versus a big one: how to judge what you are seeing
Almost everyone has noticed it. The air conditioner clicks on, the lights dip for a heartbeat, and then everything settles. In many homes this is entirely ordinary, and understanding why helps you avoid worrying about something harmless while still catching the version that is not.
The first step is to describe what you actually see. A very slight dim that lasts a fraction of a second and happens only when the compressor starts is generally the least concerning. A larger dip, where the lights go noticeably dark or flicker for a second or more, is a different story. So is a dip that happens in the whole house rather than just one room, a dip that is getting worse over time, or a dip that comes with other symptoms such as a humming sound, a tripping breaker or a burning smell. The size, duration and pattern of the dip all tell you something.
A simple way to organize what you notice is to ask a short set of questions:
- Does the dim happen every time the air conditioner starts, or only sometimes?
- Is it the same in every room, or stronger in some?
- Do other things change at the same moment, such as a television flicker, a clock reset or a fan slowing?
- Has it always been like this, or did it start recently?
- Does it happen when other large appliances start, such as the dryer or the water heater?
- Does the air conditioner itself seem to struggle to start?
Recording the answers is useful, because electricians reason from patterns. A dip that has been present since the house was built and is mild is usually a matter of normal system behavior. A dip that began right after a new air conditioner was installed may point to a circuit or connection that does not suit the new equipment. A dip that appeared after a storm may point to damage.
It is also worth knowing that different kinds of light respond differently. Older incandescent bulbs dim visibly when voltage sags, because their brightness follows the voltage closely. Many LED bulbs include electronics that hold the output steadier, so they may not dim at all for a small sag, but they can flicker or flash if the sag is large. Dimmer switches and cheap drivers can exaggerate the effect. So a house that was full of incandescent bulbs and was changed to LEDs may notice the dimming differently, which is not necessarily a sign that anything got worse.
Afternoon thunderstorms are frequent in Broward County, and pools and lanais are common in Cooper City. Both facts matter here. During warm months cooling equipment runs heavily, sometimes starting many times an afternoon, and pool equipment shares the same service. A dip that shows up mostly on the hottest afternoons often involves the combined demand of several things at once. We will take the possible causes one by one, from the harmless to the urgent.
Inrush current: the brief surge every compressor makes
An air conditioner compressor is driven by an electric motor, and, like a pool pump or a refrigerator, that motor draws a large surge of current at the instant it starts. The surge is often several times larger than the current it draws once it is running at speed. It lasts only a fraction of a second while the compressor comes up to speed, and then the current falls to its normal running level.
Every wire has some resistance, and every electrical supply has some internal impedance. When a large current flows suddenly, the voltage at the end of the wire drops for a moment. This is a basic law of electricity, sometimes described as voltage drop. The larger the current, and the longer or thinner the wire, the larger the drop. The lights in your house are connected to the same service as the air conditioner, so when the air conditioner causes a momentary drop in voltage at the panel, the lights feel it too.
Therefore a modest dip at compressor start is, in many homes, perfectly normal. It reflects the fact that a motor starting is a big event for the electrical system. Some points about why it varies from house to house:
- Size of the compressor. A larger unit has a larger starting surge.
- Distance from the panel to the unit. Longer wire runs have more drop.
- Wire size. A thinner wire drops more voltage under load.
- Strength of the supply. A house at the end of a long utility line sees more sag than one close to a transformer.
- What else is running. If the dryer or oven is already on, the total demand is higher and the sag is larger.
- Type of start. A standard start draws a strong surge, while equipment with a soft start or variable speed drive ramps up more gently and reduces dimming.
Newer air conditioners, especially those with variable speed compressors, often start much more gently and may not dim lights at all. If you have an older, single speed system and you replace it with a modern one, you may notice that the dimming disappears. If you have a modern system and the dip is large, then something else is probably contributing, and it is worth looking into.
There are also accessories called soft start kits that can be added to some compressors. They reduce the starting surge and can lessen both the dimming and the stress on the motor. They are not right for every unit, and a qualified technician should decide whether one suits your equipment. Do not add one on your own initiative.
The takeaway from all of this is that a mild dip does not by itself mean something is wrong. The electrician's job is to tell whether the size of your dip is in the expected range for your equipment and wiring, or whether it points to a weak link that deserves repair. That judgment comes from measurement, not from guessing.
Loose connections and weak links that make the dip worse
When a dip is bigger than it should be, a common culprit is a connection that has become resistive. Every point where wires join is a possible weak link: at the panel, at the breaker, at the disconnect near the outdoor unit, at the contactor inside the unit and at the terminals of the compressor itself. A connection that is perfectly tight carries current with almost no loss. A connection that has loosened, corroded or been poorly made adds resistance. Resistance means that when the current surges, extra voltage is lost across that point, and some of the energy turns into heat.
Why do connections loosen? Wires expand and contract as they warm up and cool down. Over thousands of cycles, a screw terminal can work slightly loose. Vibration from a compressor adds to the effect. In South Florida, moisture and humidity contribute corrosion, which can form a thin film between the wire and the terminal. Aluminum wiring, where it exists, is more prone to loosening at terminals because of how the metal behaves under heat, and it needs special connectors and care.
Here are some signs that a connection problem may be involved:
- The dip is larger than it used to be, without any change in equipment.
- The disconnect box near the outdoor unit feels warm or has discolored plastic or metal.
- You hear a buzz or crackle near the panel or the disconnect when the unit starts.
- One breaker feels warm, or the panel cover is warm in one spot.
- The outdoor unit has trouble starting, or shuts off suddenly and then restarts.
- Lights flicker on their own, even when the air conditioner is not starting.
That last point is significant. A loose connection in the main service or in a shared neutral can cause lights to flicker or brighten and dim at random. A shared neutral problem in particular can cause one set of lights to get brighter while another set dims, because the voltage is being unevenly divided. This is a more serious condition, since it can damage equipment connected to the circuits. If you notice lights getting noticeably brighter at the moment others dim, turn off major appliances and call an electrician promptly.
Checking these connections is a job for a qualified person. Tightening terminals in a live panel is dangerous, and the correct procedure involves turning off power, tightening to the proper specification with the right tools, and checking for damage from heat. Where a terminal shows heat damage, simply tightening may not be enough. The terminal, the breaker or the wire end may have to be replaced.
A hot connection is a fire hazard, which is why the burning smell or warm panel should be taken seriously. Turn off the related breaker if you can do so safely, keep the area clear and call for help.
Circuits that are too small, and what a bigger system asks for
The wiring that serves an air conditioner should be matched to the equipment's nameplate. The label on the outdoor unit lists two numbers that guide the choice. One is the minimum circuit ampacity, which tells the installer how large the wire must be. The other is the maximum overcurrent protection, which sets the largest breaker or fuse that is allowed. When these are followed, the circuit can carry the unit's normal and starting current safely.
Problems arise when equipment changes but the circuit does not. A common scenario: the old air conditioner was replaced with a larger one, perhaps because the family added a room or because the old one failed. The installer connected the new unit to the existing wire and breaker. If the new unit asks for more than the old circuit can provide, the wire is working harder than it should, the breaker may trip under load, and the starting surge causes a larger voltage drop than before.
Another scenario: a second system was added to an addition, a converted garage or a lanai enclosure, and it was connected to a panel that was already full. Two compressors starting within moments of each other can dim lights significantly, and they place a heavy demand on the service.
It is also common for the service as a whole to be the limiting factor. Houses built in earlier decades often have a smaller service than houses built today. A home that had a modest load when built may now run two or three cooling systems, an electric water heater, an electric dryer, a pool pump and a car charger. The service size is a ceiling for all of them. If the service is near the limit, a heavy start can pull the voltage down across the whole house.
Warning signs that the circuit or the service is undersized include:
- Breakers that trip during the hottest part of the day.
- A panel with no open spaces, with breakers doubled or tandem to squeeze in more circuits.
- Dimming that is worse when several large appliances are running.
- An outdoor disconnect or wire that feels hot.
- A recent equipment change followed by new symptoms.
The remedy depends on the finding. Sometimes a new circuit with larger wire for the cooling system solves the problem. Sometimes a subpanel or a load rearrangement is appropriate. Sometimes the service itself should be enlarged. Electricians use a load calculation, which is a standard method of adding up what the house can demand, to see whether the service has room.
If you are planning to replace your air conditioner, ask the installer to check the existing circuit against the new equipment's label and to tell you what they found. That one question prevents many future dimming and tripping problems.
Utility side and neighborhood causes you cannot fix from inside
Not every dip starts inside your walls. The electricity reaching your home passes through a chain of equipment: a transformer on a pole or pad, the wires from that transformer to your meter, and the meter itself. The utility owns and maintains much of this chain, and a weak link there can cause dimming that no amount of work inside the house will cure.
Here are some outside causes worth knowing about:
- A shared transformer that is heavily loaded. Several homes share a transformer. If many neighbors are running their air conditioners at the same time, the voltage across all of them dips together. On a hot afternoon, this can be noticeable.
- A long service line. The longer the wire from the transformer to your meter, the greater the voltage drop under load.
- Aging or damaged service wires. Wires that have been damaged by weather, tree contact or corrosion can develop resistance at splices or connections.
- A loose connection at the meter. The meter sits in a socket that grips blades. If the grip loosens or the blades corrode, resistance builds.
- Neighborhood events. A large motor starting nearby, such as at a business or a pump station, can cause brief dips for homes on the same line.
How do you tell whether the issue is outside? A few observations help. If neighbors notice the same dimming at the same moment, the cause is likely outside your home. If the dimming appears or worsens during hot afternoons across the neighborhood, load on a shared transformer is a suspect. If the lights in your house brighten and dim in a random pattern that does not match your own appliances, a loose connection on the utility side could be involved. A flicker that follows a storm is also a clue.
If you suspect the problem is on the utility side, contact the utility and describe what you see, when it happens and whether neighbors are affected. They can check their equipment. Do not open the meter or touch the service wires. The meter and the lines leading to it are the utility's responsibility and are dangerous to handle. If you see sparking, burning or arcing at the meter, stay away and call the utility's emergency line and emergency services.
An electrician can help by measuring the voltage at your panel with and without the air conditioner running. If the voltage at the panel sags significantly while the wiring inside the house is sound, the evidence supports a utility side problem, and you can pass those measurements to the utility. This kind of documentation makes the utility's work faster and your conversation with them more productive.
During storm season, momentary outages and brief voltage sags may become more common as the grid reacts to lightning and wind. Surge protection at the panel helps protect equipment from spikes, though it cannot fix a weak supply.
How an electrician diagnoses the dip and what the fix might be
A good diagnosis starts with listening. The electrician will ask the questions listed at the start of this guide, and probably a few more. Then comes a methodical set of steps, designed to narrow the possibilities.
First, observation. With the air conditioner off, the electrician checks the panel, the breakers and the disconnect for signs of heat, corrosion or looseness. Next, they measure the voltage at the panel with no load, so they know the starting point. Then they watch what happens to the voltage when the air conditioner starts. A measuring instrument that captures the lowest point of the dip shows how large the sag actually is. A sag of modest size is normal. A deep sag points to a weak supply or a resistive connection.
Second, isolation. To find where the voltage is being lost, the electrician measures at several points: at the meter, at the main breaker, at the air conditioner breaker and at the outdoor disconnect. The place where the voltage falls sharply identifies the weak link. If the loss is between the transformer and the meter, the utility is involved. If it is between the meter and the panel, the service equipment may be at fault. If it is between the panel and the unit, the circuit or its connections need attention.
Third, repair. Possible fixes include:
- Cleaning and tightening connections, or replacing terminals, breakers or wire ends that show heat damage.
- Replacing a worn contactor or capacitor in the outdoor unit, which is typically done by a heating and cooling technician in cooperation with the electrician.
- Installing a larger wire for the air conditioner circuit if the existing one is undersized.
- Adding a soft start device where the manufacturer allows it.
- Upgrading the service or adding a subpanel if the overall capacity is limiting.
- Working with the utility to correct a problem on their equipment.
Fourth, verification. After the repair, the electrician repeats the measurement to confirm that the dip has improved. A result that can be measured is more trustworthy than a feeling.
What about permits? Replacing a circuit, enlarging a service or adding a subpanel normally requires a permit and an inspection in Broward County. Minor repairs like tightening a connection or replacing a breaker may not. Ask the electrician which applies.
Meanwhile, you can take a few precautions at home. Keep the area around the panel clear. Avoid running multiple large appliances at the moment the air conditioner starts, if you are noticing a strain. Do not replace breakers with larger ones. If the unit struggles to start, turn it off at the thermostat and call, because repeated hard starts shorten its life.
If you have a dip that bothers you, call and describe it. A quote can begin by phone once we understand the pattern, and because this involves the panel, the service and equipment outdoors, an on site visit is needed before the fix is final.